ATMEGA328 TQFP PDF

The Atmel® picoPower® ATmega/P is a low-power CMOS 8-bit microcontroller 8-channel bit ADC in TQFP and QFN/MLF package. •. Temperature. Atmel high performance, low power 8-bit AVR ATmegaP-AU microcontroller in the TQFP package. Okay, so I’m about to blow up. I’ve tried to use perhaps 10 Atmega TQFP without any success.

Author: Aragami Zulkidal
Country: Dominica
Language: English (Spanish)
Genre: Education
Published (Last): 17 March 2015
Pages: 199
PDF File Size: 7.10 Mb
ePub File Size: 13.8 Mb
ISBN: 475-7-73851-156-7
Downloads: 45729
Price: Free* [*Free Regsitration Required]
Uploader: Meztikasa

ATMega328 – TQFP

By using our site, you acknowledge that you have read and understand our Cookie PolicyPrivacy Policyand our Terms of Service. I’ve simply connected the AVR programmer to the chip in the adapter socket as follows AVR connector on left, chip on right. However, when attempting to upload the bootloader to the chip, I am presented with the following error:.

Clearly I’m doing something incorrectly, and I wouldn’t doubt if it was because it’s not as simple as hooking the AVR programmer directly up to the chip to program it.

[Solved]Cannot upload sketch to Atmegap TQFP soldered on PCB

This question does not appear to be about electronics design within the scope defined in the help center. If this question can be reworded to fit the rules in the help centerplease edit the question. Well first of all, check the wiring. Check that the ISP header atmrga328 to the pins that it ought to, and check that tqp have the chip oriented correctly in the socket The USBtiny has a switch to power the target, so make sure that’s in the correct position.

  JUAN GABRIEL TOKATLIAN PDF

If all that is correct, there are a couple other things that could cause that error:. The reset pin lacks the normal ESD protection, and so is fairly easy to fry.

ATmega328P Microcontroller – TQFP

Ground yourself and use an ESD mat. If you have ever managed to program the fuses, the reset pin may have been disabled, or the device may be expecting an external crystal.

If the reset pin has been disabled, you’ll need a special high voltage 12V programmer to gqfp it. Assuming your connection is incorrect, first you need to add a pull-up resistor to the reset pin; 1kk should be alright. That is pretty much all you need. Home Questions Tags Users Unanswered.

ATmegaP Chip Erase delay: SCK serial program mode: Block Poll Page Polled Memory Type Mode Delay Size Indx Paged Size Size Pages MinW MaxW ReadBack eeprom 65 20 4 0 no 4 0 0xff 0xff flash 65 6 0 yes tqqfp 0xff lfuse 0 0 0 0 no 1 0 0 0x00 0x00 hfuse 0 0 0 0 no 1 0 0 0x00 0x00 efuse 0 0 0 0 no 1 0 0 0x00 0x00 lock 0 0 0 0 no 1 0 0 0x00 0x00 calibration 0 0 0 0 no 1 0 0 0 0 0x00 0x00 signature 0 0 0 0 no 3 0 0 0 0 0x00 0x00 Programmer Type: Using SCK period of 10 usec atemga328 Error while burning bootloader.

  ELECTROREFINING OF GOLD PDF

Any help would be appreciated. Can you edit the question to include the exact command-line atmgea328 given to avrdude?

It hqfp like the log text says ‘programmer operation not supported’, could be a symptom of bad cmd line args. Have you applied power to the circuit? The AVR programmer will not supply power. TomCarpenter, the programmer does provide power. It’s worth checking its in the correct position, though.

ATmega – Wikipedia

I’m voting to close this question as off-topic because it has been abandoned for half a year in atega328 state. If all that is correct, there are a couple other things that could cause that error: Crystal requirement comes when booting through the bootloader i.

When programming through SPI, the chip accepts the program even if the fuses are set to accept clock signal from external clock. ISP requires a working clock source.

Only HV programming does not. Atmega 2 9 Reset is driven by the programmer, and besides has an internal pullup.